Tools

Replacement shaft for Micro Bearing Press - 1/4" shaft diameter - 12" length

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

This simple tool is designed to remove and install the static bearing in the shock ends of many modern rear shocks. Machined from durable stainless steel this compact tool allows the user to remove and install the DU bushings without resorting to hammers and punches. The coarse acme thread keeps the constant turning to a minimum.

1/8" mid plate, needed to use the Decade chain tool with wide 1/8" track and single speed chains.

For use with the Decade Chain Tool this AXS Mid Plate is required for the SRAM AXS Road and the new MTB Transmission Flat Top chains. This part is not needed for other 12spd chains from various manufacturers. The mid plate is visually differentiated from the other Decade mid plates by three dots on the face of the plate.

Replacement pins, these are original equipment chain pins for our chain tool, they also work as an alternate to the Campagnolo UT-CN300 11spd chain tool, Shimano CN-34 and CN-32 Sold in pairs.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. The Fork Seal Press is built with modern tight fitting fork seals in mind. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.

Replacement feeler gauge for the Abbey Hanger Alligment Gauge Tool.

Replacement threaded cap for Abbey Hanger Alligment Gauge Tool.

This bottom bracket socket is for use with Chris King's T47 Bottom Bracket. Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket. This socket features a threaded boss to allow you to bolt the tool into place when dealing with these exceptionally thin tool interfaces. This is a feature unique to our tools that adds a layer of protection and security to your parts and tools.

Replacement 6/8mm Hex bit for both the Abbey BBQ Wood Handled Pedal Wrench and the Team Issue Pedal Wrench.

The Charger 2 wrench is designed for use on the lower seal head of Charger 2 and Charger LT dampers. This series of wrenches comes as a result of our collaboration with RockShox to develop a series of tools specifically for their suspension components. Built to hold the thin aluminum parts of the dampers to avoid damage. These wrenches are built with the same tool grade aluminum to tight tolerances to give you years of trouble free use. They will not damage or mar the sensitive parts inside your suspension fork when used with care, keeping you and your customers happy. They also feature a 3/8" square drive in the middle to use with your favorite torque wrench during reassembly.

The Reverb is an advanced and complicated component and service becomes a breeze with this speciality wrench. Designed for use on the inner seal head and upper collet of both 30.9 and 31.6 millimeter version of the Reverb dropper post. This series of wrenches comes as a result of our collaboration with RockShox to develop a series of tools specifically for their suspension components. Built to hold the thin aluminum parts of the dampers to avoid damage. These wrenches are built with the same tool grade aluminum to tight tolerances to give you years of trouble free use. They will not damage or mar the sensitive parts inside your seastpost when used with care, keeping you and your customers happy. They also feature a 3/8" square drive in the middle to use with your favorite torque wrench during reassembly.

Many athletes are fortunate enough to be able to ride nearly anything. For those that are sensitive to bike fit though, replicating fit to a new bike or confirming fit after travel can be a challenge involving lots of trial and error. This set of tools allows accurate and repeatable measurements for saddle height, angle and setback. The accuracy and repeatable measurements also serve as a base to make adjustments to fit. -The magnetic saddle height bullets ensure you get an accurate center at the BB by locating in the crank arm fixing bolt or the crank arm preload cap of Shimano caps. This allows you to focus on the smart end of the tape measure at the saddle plate. -Two reference marks on the saddle plate means you can pull a measurement to the exact same spot relative to the nose of the saddle every time. This gives you accuracy down to a single millimeter. -The front of the saddle plate is engraved with a ruler, to allow you to calculate saddle setback at the saddle. This allows you to drop the plumb bob off the side of the bike and clear all of the bottle cages. -The wide plate has ample room to mount a level, protractor or smart phone for adjusting the angle of the saddle. This is particularly helpful for non traditional saddles like SMP and Adamo.

The Shimano Crank Tool (SCT for short) is specifically built to service the chainring lockring on Shimano single ring cranksets for 12 speed drivetrains. It features a large hex that can be used with a 1.5" or 38mm wrench or locked into a vise. The clearance hole is kept to a minimum to keep the tool engaged on the low profile lockring, minimizing the chance of damaging the tool or parts. Compatibility: - Chain ring lockrings on Shimano 12spd mountain crank sets. - XT and Ultegra bottom brackets

The Shop Hammer has a heat-treated 1.5-inch (38mm) stainless steel head and 12-inch long handle with the same silicone grip from ESI as our Team Issue Hammer. Weighing in at a respectably stout 20oz (566g), they are sure to make short work of setting crown races and removing press fit bottom brackets. - Hammer comes standard with green soft face. Brass tips are also available. - Made in Bend, Oregon

The Brass Face for the Shop Hammer is a fantastic option when hammering on metal and you need something softer than the material your are pounding on.

With a 15mm box end on one end and a custom 6 and 8 millimeter swivel bit on the opposite end, it's the only pedal wrench you'll ever need. Perfect to keep at the fit station, on the sales floor, and at the tool bench. The shop version of the tool gets an extra 6" (15cm) of leverage over the team issue for an overall length of 18 inches. Great for removing those stubborn pedals. - Durable black Cerakote finish - Made in Bend, Oregon

All the awesomeness of the dual-sided tool but in a single Shimano or Campagnolo version. Updated in 2020, the single-sided tool now has the same size handle (1/2 inch) as the dual-sided tool. - When purchasing the chain whip, buy the 1/2-inch handle chain whip.

We listened to your requests and created a socket style Crombie tool that is compatible with ratchets and torque wrenches. The Socket Crombie has our signature finger spline at the top along with a 3/8" square drive for using your favorite ratchet or torque wrench. The tool is plenty deep to hide a quick release and still get full engagement on the lock ring. Compatible with all Campagnolo cassettes.

The Socket Crombie has our signature finger spline at the top along with a 3/8" square drive for using your favorite ratchet or torque wrench. The tool is plenty deep to hide a quick release and still get full engagement on the lock ring. The S Group Socket Crombie is ideal for some of the newer RockShox suspension forks that are using the S group lockring spline for suspension top caps. It is also compatible with all modern Shimano and Sram cassettes.

With a 15mm box end on one end and a custom 6 and 8 millimeter hex swivel bit on the opposite end, it's the only pedal wrench you'll ever need. Perfect to keep at the fit station, on the sales floor, and at the tool bench. Weighing 286 grams, this is a great travel tool for cyclists or mechanics that don't want to sacrifice usability for weight savings.